74F193 Просмотр технического описания (PDF) - Philips Electronics

Номер в каталоге

Компоненты Описание

Список матч

74F193

Up/down binary counter with separate up/down clocks

Philips Electronics 

Philips Semiconductors

Up/down binary counter with separate up/down clocks

Product specification

74F193

FEATURES

• Synchronous reversible 4-bit counting

• Asynchronous parallel load capability

• Asynchronous reset (clear)

• Cascadable without external logic

DESCRIPTION

The 74F193 is a 4-bit synchronous up/down counter in the binary

mode. Separate up/down clocks, CPU and CPD respectively,

simplify operation. The outputs change state synchronously with the

Low-to-High transition of either clock input. If the CPU clock is

pulsed while CPD is held High, the device will count up. If CPD clock

is pulsed while CPU is held High, the device will count down. The

device can be cleared at any time by the asynchronous reset pin. It

may also be loaded in parallel by activating the asynchronous

parallel load pin.

Inside the device are four master-slave JK flip-flops with the

necessary steering logic to provide the asynchronous reset,

asynchronous preset, load, and synchronous count up and count

down functions.

Each flip-flop contains JK feedback from slave to master, such that a

Low-to-High transition on the CPD input will decrease the count by

one, while a similar transition on the CPU input will advance the

count by one.

One clock should be held High while counting with the other,

because the circuit will either count by twos or not at all, depending

on the state of the first JK flip-flop, which cannot toggle as long as

either clock input is Low. Applications requiring reversible operation

must make the reversing decision while the activating clock is High

to avoid erroneous counts.

The Terminal Count Up (TCU) and Terminal Count Down (TCD)

outputs are normally High. When the circuit has reached the

maximum count state of 15, the next High-to-Low transition of CPU

will cause TCU to go Low. TCU will stay Low until CPU goes High

again, duplicating the count up clock, although delayed by two gate

delays. Likewise, the TCD output will go Low when the circuit is in

the zero state and the CPD goes Low. The TC outputs can be used

as the clock input signals to the next higher order circuit in a

multistage counter, since they duplicate the clock waveforms.

Multistage counters will not be fully synchronous since there is a

two-gate delay time difference added for each stage that is added.

The counter may be preset by the asynchronous parallel load

capability of the circuit. Information present on the parallel Data

inputs (D0 - D3) is loaded into the counter and appears on the

outputs regardless of the conditions of the clock inputs when the

Parallel Load (PL) input is Low. A High level on the Master Reset

(MR) input will disable the parallel load gates, override both clock

inputs, and set all Q outputs Low. If one of the clock inputs is Low

during and after a reset or load operation, the next Low-to-High

transition of the clock will be interpreted as a legitimate signal and

will be counted.

TYPE

74F193

TYPICAL fMAX

125MHz

TYPICAL

SUPPLY CURRENT

(TOTAL)

32mA

ORDERING INFORMATION

DESCRIPTION

16-pin plastic DIP

COMMERCIAL RANGE

VCC = 5V ±10%,

Tamb = 0°C to +70°C

N74F193N

16-pin plastic SO

N74F193D

PKG DWG #

SOT38-4

SOT109-1

PIN CONFIGURATION

D1 1

Q1 2

Q0 3

CPD 4

CPU 5

Q2 6

Q3 7

GND 8

16 VCC

15 D0

14 MR

13 TCD

12 TCU

11 PL

10 D2

9 D3

SF00745

INPUT AND OUTPUT LOADING AND FAN-OUT TABLE

PINS

DESCRIPTION

74F(U.L.)

HIGH/LOW

D0 - D3

Data inputs

1.0/1.0

CPU

Count up clock input (active rising edge)

CPD

Count down clock input (active rising edge)

PL

Asynchronous parallel load control input (active Low)

1.0/3.0

1.0/3.0

1.0/1.0

MR

Asynchronous master reset input

1.0/1.0

Q0 - Q3

Flip-flop outputs

50/33

TCU

Terminal count up (carry) output (active Low)

50/33

TCD

Terminal count down (borrow) output (active Low)

50/33

NOTE: One (1.0) FAST Unit Load (U.L.) is defined as: 20µA in the High state and 0.6mA in the Low state.

LOAD VALUE

HIGH/LOW

20µA/0.6mA

20µA/1.8mA

20µA/1.8mA

20µA/0.6mA

20µA/0.6mA

1.0mA/20mA

1.0mA/20mA

1.0mA/20mA

1995 Jul 17

2

853-0353 15459

Share Link: