IDT54FCT388915T70PYB Просмотр технического описания (PDF) - Integrated Device Technology
Номер в каталоге
Компоненты Описание
Список матч
IDT54FCT388915T70PYB
Integrated Device Technology
IDT54FCT388915T70PYB Datasheet PDF : 11 Pages
| |||
IDT54/74FCT388915T 70/100/133/150
3.3V LOW SKEW PLL-BASED CLOCK DRIVER
MILITARY AND COMMERCIAL TEMPERATURE RANGES
ABSOLUTE MAXIMUM RATINGS(1)
Symbol
Rating
VTERM(2) Terminal Voltage
with Respect to
GND
VTERM(3) Terminal Voltage
with Respect to
GND
VTERM(4) Terminal Voltage
with Respect to
GND
Commercial Military Unit
–0.5 to +4.6 –0.5 to +4.6 V
–0.5 to +7.0 –0.5 to +7.0 V
–0.5 to VCC –0.5 to VCC V
+0.5
+0.5
TA
Operating
Temperature
0 to +70 –55 to +125 °C
TBIAS
Temperature
Under Bias
–55 to +125 –65 to +135 °C
TSTG
Storage
Temperature
–55 to +125 –65 to +150 °C
IOUT
DC Output
Current
–60 to +60 –60 to +60 mA
NOTES:
3052 tbl 02
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RAT-
INGS may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions
above those indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating conditions for ex-
tended periods may affect reliability.
2. Vcc terminals.
3. Input terminals.
4. Output and I/O terminals.
CAPACITANCE (TA = +25°C, f = 1.0MHz)
Symbol Parameter(1) Conditions Typ. Max. Unit
CIN
Input
VIN = 0V
4.5 6.0 pF
Capacitance
COUT Output
VOUT = 0V 5.5 8.0 pF
Capacitance
NOTE:
3052 lnk 03
1. This parameter is measured at characterization but not tested.
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Commercial: TA = 0°C to 70°C, VCC = 3.3V ±0.3V
Symbol
VIH
Parameter
Input HIGH Level
Test Conditions(1)
Guaranteed Logic HIGH Level
Min.
2.0
Typ.(2)
—
Max.
5.5
VIL
Input LOW Level
Guaranteed Logic LOW Level
–0.5
—
0.8
II H
Input HIGH Current
VCC = Max.
VI = 5.5V
—
—
±1
II L
Input LOW Current
VI = GND
—
—
±1
IOZH
High Impedance Output Current VCC = Max.
VO = VCC
—
—
±1
IOZL
(3-State Output Pins)
VO = GND
—
—
±1
VIK
IODH
IODL
VOH
Clamp Diode Voltage
Output Drive Current
Output Drive Current
Output HIGH Voltage
VCC = Min., IIN = –18mA
VCC = Max., VIN = VIH or VIL, VO = 1.5V(3)
VCC = Max., VIN = VIH or VIL, VO = 1.5V(3)
VCC = Min.
IOH = –16mA
—
–36
50
2.4(5)
–0.7
—
—
3.0
–1.2
—
—
—
VOL
Output LOW Voltage
VCC = Min.
IOL = 32mA
—
0.3
0.5
VH
Input Hysteresis
—
—
100
—
ICCL
ICCH
ICCZ
Quiescent Power Supply Current VCC = Max., VIN = GND or VCC
(Test mode)
—
2.0
4.0
NOTES:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 3.3V, +25°C ambient.
3. Not more than one output should be tested at one time. Duration of the test should not exceed one second.
4. This parameter is guaranteed but not tested.
5. VOH = VCC - 0.6V at rated current.
Unit
V
V
µA
µA
µA
µA
V
mA
mA
V
V
mV
mA
3052 tbl 04
9.8
3
Share Link: