AD8340 Просмотр технического описания (PDF) - Analog Devices

Номер в каталоге

Компоненты Описание

Список матч

AD8340

700 MHz to 1000 MHz RF Vector Modulator

Analog Devices 

Data Sheet

AD8340

Table 4. Evaluation Board Configuration Options

Components

Description

R7, R9, R11, R14,

R15, R19, R20, R21,

C15, C19, W3, W4

I Channel Baseband Interface. Resistor R7 and Resistor R9 can be

installed to accommodate a baseband source that requires a

specific terminating impedance. C15 and C19 are bypass

capacitors. For single-ended baseband drive, Potentiometer R11

can be used to provide a bias level to the unused input (install

either W3 or W4).

R1, R3, R10, R12,

R13, R16, R17, R18,

C16, C20, W1, W2

Q Channel Baseband Interface. See the I Channel Baseband

Interface description.

C11, C12

T1, C17, C18, L1, L2

L3, L4, C5, C6

C2, C4, C7, C9, C14,

C1, C3, C8, C10,

R2, R4, R5, R6

R8, SW1

Baseband Low-Pass Filtering. By adding Capacitor C11 between

QFLP and QFLM, and Capacitor C12 between IFLP and IFLM, the

3 dB low-pass corner frequency of the baseband interface can be

reduced from 230 MHz (nominal). See the equation in the

Evaluation Board section.

Output Interface. The 1:1 balun transformer, T1, converts the 50 Ω

differential output to 50 Ω single-ended. C17 and C18 are dc

blocks. L1 and L2 provide dc bias for the output.

Input Interface. The input impedance of the AD8340 requires 5.6 nH

inductors in series with RFIP and RFIM for optimum return loss

when driven by a single-ended 50 Ω line. C5 and C6 are dc blocks.

Supply Decoupling.

Output Disable Interface. The output stage of the AD8340 is

disabled by applying a high voltage to the DSOP pin by moving

SW1 to Position B. The output stage is enabled by moving SW1 to

Position A. The output disable function can also be exercised by

applying an external high or low voltage to the DSOP SMA

connector with SW1 in Position A.

Default Conditions

R7, R9 = open

R11 = potentiometer, 2 kΩ, 10 turns (Bourns)

R14 = 4 kΩ (Size 0603)

R15 = 44 kΩ (Size 0603)

R19, R20, R21 = 0 Ω (Size 0603)

C15, C19 = 0.1 µF (Size 0603)

W3 = jumper (installed)

W4 = jumper (open)

R1, R3 = open

R10 = potentiometer, 2 kΩ, 10 turns (Bourns)

R12 = 4 kΩ (Size 0603)

R13 = 44 kΩ (Size 0603)

R16, R17, R18 = 0 Ω (Size 0603)

C16, C20 = 0.1 µF (Size 0603)

W1 = jumper (installed)

W2 = jumper (open)

C11, C12 = open

C17, C18 = 100 pF (Size 0603)

T1 = ETC1-1-13 (M/A-COM)

L1, L2 = 120 nH (Size 0603)

L3, L4 = 5.6 nH (Size 0402)

C5, C6 = 100 pF (Size 0603)

C2, C4, C7, C9 = open (Size 0603)

C1, C3, C8, C10, C14 = 0.1 µF (Size 0603)

R2, R4, R5, R6 = 0 Ω (Size 0603)

R8 = 10 kΩ (Size 0603)

SW1 = SPDT (Position A, output enabled)

Rev. C | Page 17 of 20

Share Link: