AD7783 Просмотр технического описания (PDF) - Analog Devices

Номер в каталоге

Компоненты Описание

Список матч

AD7783

Read-Only, Pin Configured 24-Bit Σ-Δ ADC with Excitation Current Sources

Analog Devices 

AD7783

PIN CONFIGURATION

XTAL1 1

16 XTAL2

REFIN(+) 2

15 VDD

REFIN(–) 3

14 GND

AIN(+) 4 AD7783 13 MODE

AIN(–)

5

TOP VIEW

(Not to Scale)

12

DOUT/RDY

IOUT1 6

11 CS

IOUT2 7

10 SCLK

IPIN 8

9 RANGE

PIN FUNCTION DESCRIPTIONS

Pin No. Mnemonic Function

1

XTAL1

Input to the 32.768 kHz Crystal Oscillator Inverter.

2

REFIN(+) Positive Reference Input. REFIN(+) can lie anywhere between VDD and GND + 1 V. The nominal refer-

ence voltage (REFIN(+) – REFIN(–)) is 2.5 V, but the part functions with a reference from 1 V to VDD.

3

REFIN(–) Negative Reference Input. This reference input can lie anywhere between GND and VDD – 1 V.

4

AIN(+)

Analog Input. AIN(+) is the positive terminal of the fully differential analog input pair AIN(+)/AIN(–).

5

AIN(–)

Analog Input. AIN(–) is the negative terminal of the fully differential analog input pair AIN(+)/AIN(–).

6

IOUT1

Output from Internal 200 mA Excitation Current Source. Either current source IEXC1 or IEXC2 can be

switched to this output using hardware control pin IPIN.

7

IOUT2

Output from Internal 200 mA Excitation Current Source. Either current source IEXC1 or IEXC2 can be

switched to this output using hardware control pin IPIN.

8

IPIN

Logic Input that Selects the Routing of the On-Chip Current Sources. When IPIN is tied to GND, IEXC1

is routed to IOUT1 and IEXC2 is routed to IOUT2. When IPIN is tied to VDD, IEXC1 is routed to

IOUT2 and IEXC2 is routed to IOUT1.

9

RANGE

Logic Input that Configures the Input Range on the Internal PGA. With RANGE = 0, the full-scale input

range is ± 160 mV; the full-scale input range equals ± 2.56 V when RANGE = 1 for a 2.5 V reference.

10

SCLK

Serial Clock Input/Output for Data Transfers from the ADC. When the device is operated in master mode,

SCLK is an output with one SCLK period equal to one XTAL period. In slave mode, SCLK is generated

by an external source. In slave mode, all the data can be transmitted on a continuous train of pulses. Alter-

natively, it can be a noncontinuous clock with the information being transmitted from the AD7783 in

smaller batches of data. SCLK is Schmitt triggered (slave mode), making the interface suitable for opto-

isolated applications.

11

CS

Chip Select Input. CS is an active low logic input used to select the AD7783. When CS is low, the PLL

establishes lock and allows the AD7783 to initiate a conversion. When CS is high, the conversion is aborted,

DOUT and SCLK are three-stated, the AD7783 enters standby mode, and any conversion result in the

output shift register is lost.

12

DOUT/RDY Serial Data Output/Data Ready Output. DOUT/RDY serves a dual purpose in this interface. When a conver-

sion is initiated, DOUT/RDY goes high and remains high until the conversion is complete. DOUT/RDY will

then return low to indicate that valid data is available to be read from the device. In slave mode, this acts as

an interrupt to the processor, indicating that valid data is available. If data is not read after a conversion,

DOUT/RDY will go high before the next update occurs. In master mode, DOUT/RDY goes low for at

least half an SCLK cycle before the device produces SCLKs. When SCLK becomes active, data is output

on the DOUT/RDY pin. Data is output on the falling SCLK edge and is valid on the rising edge.

13

MODE

The MODE pin selects master or slave mode of operation. When MODE = 0, the AD7783 operates in

master mode; the AD7783 is configured for slave mode when MODE = 1.

14

GND

Ground Reference Point for the AD7783.

15

VDD

Supply Voltage, 3 V or 5 V Nominal.

16

XTAL2

Output from the 32.768 kHz Crystal Oscillator Inverter.

–6–

REV. C

Share Link: