AD7482BSTZ Просмотр технического описания (PDF) - Analog Devices

Номер в каталоге

Компоненты Описание

Список матч

AD7482BSTZ

3 MSPS, 12-Bit SAR ADC

Analog Devices 

For higher input bandwidth applications, the AD8021 op amp

(also available as a dual AD8022 op amp) is the recommended

choice to drive the AD7482. Figure 15 shows the analog input

circuit used to obtain the data for the FFT plot shown in Figure 4. A

bipolar analog signal is applied to the terminal and biased up with a

stable, low noise dc voltage connected, as shown in Figure 12. A

10 pF compensation capacitor is connected between Pin 5 of the

AD8021 and the negative supply. The AD8021 is supplied with

+12 V and −12 V supplies. The supply pins are decoupled as close

to the device as possible, with both a 0.1 μF anad10 μF capacitor

connected to each pin. In each case, the 0.1 μF capacitor should

be the closer of the two caps to the device. The AD8021 logic

reference pin is tied to analog ground and the DISABLE Pin is

tied to the positive supply, as shown in Figure 12. Detailed

information on the AD8021 is available at www.analog.com.

ADC TRANSFER FUNCTION

The output coding of the AD7482 is straight binary. The designed

code transitions occur midway between the successive integer

LSB values, that is, 1/2 LSB, 3/2 LSB, and so on. The LSB size is

VREF/4096. The nominal transfer characteristic for the AD7482 is

shown in Figure 16. This transfer characteristic may be shifted

as detailed in the Offset/Overrange section.

111...111

111...110

111...000

011...111

1LSB = VREF/4096

000...010

000...001

000...000

0V 0.5LSB

+VREF – 1.5LSB

ANALOG INPUT

Figure 16. AD7482 Transfer Characteristic

POWER SAVING

The AD7482 uses advanced design techniques to achieve very

low power dissipation at high throughput rates. In addition, the

AD7482 features two power saving modes, nap and standby. These

modes are selected by bringing either the NAP pin or STBY pin

to a logic high, respectively.

When operating the AD7482 in normal fully powered mode,

the current consumption is 18 mA during conversion and the

quiescent current is 12 mA. Operating at a throughput rate of

1 MSPS, the conversion time of 300 ns contributes 27 mW to

the overall power dissipation.

(300 ns/1 μs) × (5 V × 18 mA) = 27 mW

AD7482

For the remaining 700 ns of the cycle, the AD7482 dissipates

42 mW of power.

(700 ns/1 μs) × (5 V × 12 mA) = 42 mW

Therefore, the power dissipated during each cycle is

27 mW + 42 mW = 69 mW

Figure 17 shows the AD7482 conversion sequence operating in

normal mode.

1µs

CONVST

BUSY

300ns

700ns

Figure 17. Normal Mode Power Dissipation

In nap mode, almost all the internal circuitry is powered down.

In this mode, the power dissipation is reduced to 2.5 mW. When

using an external reference, there must be a minimum of 300 ns

from exiting nap mode to initiating a conversion. This is necessary

to allow the internal circuitry to settle after power-up and for

the track-and-hold to properly acquire the analog input signal.

The internal reference cannot be used in conjunction with the

nap mode.

If the AD7482 is put into nap mode after each conversion, the

average power dissipation is reduced, but the throughput rate is

limited by the power-up time. Using the AD7482 with a through-

put rate of 500 kSPS while placing the part in nap mode after

each conversion results in average power dissipation as follows:

The power-up phase contributes

(300 ns/2 μs) × (5 V × 12 mA) = 9 mW

The conversion phase contributes

(300 ns/2 μs) × (5 V × 18 mA) = 13.5 mA

While in nap mode for the rest of the cycle, the AD7482

dissipates only 1.75 mW of power.

(1400 ns/2 μs) × (5 V × 0.5 mA) = 1.75 mW

Therefore, the power dissipated during each cycle is

9 mW + 13.5 mW + 1.75 mW = 24.25 mW

Rev. B | Page 13 of 20

Share Link: