74ALVT16260 Просмотр технического описания (PDF) - Philips Electronics

Номер в каталоге

Компоненты Описание

Список матч

74ALVT16260

12-bit to 24-bit multiplexed D-type latches (3-State)

Philips Electronics 

Philips Semiconductors

2.5V/3.3V 12-bit to 24-bit multiplexed D-type latches

(3-State)

Product specification

74ALVT16260

DC ELECTRICAL CHARACTERISTICS (2.5V "0.2V RANGE)

LIMITS

SYMBOL

PARAMETER

TEST CONDITIONS

Temp = -40°C to +85°C UNIT

MIN TYP1 MAX

VIK

Input clamp voltage

VCC = 2.3V; IIK = –18mA

–0.85 –1.2

V

VOH

High-level output voltage

VCC = 2.3 to 3.6V; IOH = –100µA

VCC = 2.3V; IOH = –8mA

VCC–0.2 VCC

V

1.8

2.1

VOL

Low-level output voltage

VCC = 2.3V; IOL = 100µA

VCC = 2.3V; IOL = 24mA

0.07 0.2

0.3 0.5

VRST Power-up output low voltage7 VCC = 2.7V; IO = 1mA; VI = VCC or GND

0.55

V

VCC = 2.7V; VI = VCC or GND

Control pins

0.1

±1

II

Input leakage current

VCC = 0 or 2.7V; VI = 5.5V

VCC = 2.7V; VI = VCC

VCC = 2.7V; VI = 0

Data pins4

0.1

10

µA

0.1

1

0.1

-5

IOFF

Off current

VCC = 0V; VI or VO = 0 to 4.5V

0.1 "100 µA

IHOLD

Bus Hold current

Data inputs6

VCC = 2.3V; VI = 0.7V

VCC = 2.3V; VI = 1.7V

90

µA

–10

IEX

Current into an output in the

High state when VO > VCC

VO = 5.5V; VCC = 2.3V

10

125

µA

IPU/PD

Power up/down 3-State output VCC ≤ 1.2V; VO = 0.5V to VCC; VI = GND or VCC;

current3

OE/OE = Don’t care

1

100 µA

IOZH 3-State output High current

VCC = 2.7V; VO = 2.3V; VI = VIL or VIH

0.5

5

µA

IOZL

3-State output Low current

VCC = 2.7V; VO = 0.5V; VI = VIL or VIH

0.5

–5

µA

ICCH

VCC = 2.7V; Outputs High, VI = GND or VCC, IO = 0

0.04 0.1

ICCL

ICCZ

Quiescent supply current

VCC = 2.7V; Outputs Low, VI = GND or VCC, IO = 0

VCC = 2.7V; Outputs Disabled; VI = GND or VCC, IO = 05

2.7 4.5 mA

0.04 0.1

∆ICC

Additional supply current per

input pin2

VCC = 2.3V to 2.7V; One input at VCC–0.6V,

Other inputs at VCC or GND

0.04 0.4 mA

NOTES:

1. All typical values are at VCC = 2.5V and Tamb = 25°C.

2. This is the increase in supply current for each input at the specified voltage level other than VCC or GND

3. This parameter is valid for any VCC between 0V and 1.2V with a transition time of up to 10msec. From VCC = 1.2V to VCC = 2.5V ± 0.3V a

transition time of 100µsec is permitted. This parameter is valid for Tamb = 25°C only.

4. Unused pins at VCC or GND.

5. ICCZ is measured with outputs pulled up to VCC or pulled down to ground.

6. Not guaranteed.

7. For valid test results, data must not be loaded into the flip-flops (or latches) after applying power.

1998 Jan 30

8

Share Link: