Introduction
The MC68HC912D60A microcontroller unit (MCU) is a 16-bit device available in two package options, 80-pin QFP and 112-pin TQFP. On chip peripherals include a 16-bit central processing unit (CPU12), 60K bytes of flash EEPROM, 2K bytes of RAM, 1K bytes of EEPROM, two asynchronous serial communication interfaces (SCI), a serial peripheral interface (SPI), an enhanced capture timer (ECT), two (one on 80QFP) 8-channel,10-bit analog-to-digital converters (ATD), a four-channel pulse-width modulator (PWM), and a CAN 2.0 A, B software compatible module (MSCAN12). System resource mapping, clock generation, interrupt control and bus interfacing are managed by the lite integration module (LIM). The MC68HC912D60A has full 16-bit data paths throughout, however, the external bus can operate in an 8-bit narrow mode so single 8-bit wide memory can be interfaced for lower cost systems. The inclusion of a PLL circuit allows power consumption and performance to be adjusted to suit operational requirements. In addition to the I/O ports available in each module, 16 (2 on 80QFP) I/O port pins are available with Key-Wake-Up capability from STOP or WAIT mode.

FEATUREs
• 16-bit CPU12
   – Upward compatible with M68HC11 instruction set
   – Interrupt stacking and programmer’s model identical to M68HC11
   – 20-bit ALU
   – Instruction queue
   – Enhanced indexed addressing
• Multiplexed bus
   – Single chip or expanded
   – 16 address/16 data wide or 16 address/8 data narrow mode
   • Two 8-bit ports with key wake-up interrupt (2 pins only are available on 80QFP) and one I2C start bit detector (112TQFP only)
• Memory
   – 60K byte flash EEPROM, made of a 28K module and a 32K module with 8K bytes protected BOOT section in each module (MC68HC912D60A)
   – 1K byte EEPROM
   – 2K byte RAM
• Analog-to-digital converters
   – 2 x 8-channels, 10-bit resolution in 112TQFP
   – 1 x 8-channels, 8-bit resolution in 80QFP
• 1M bit per second, CAN 2.0 A, B software compatible module
   – Two receive and three transmit buffers
   – Flexible identifier filter programmable as 2 x 32 bit, 4 x 16 bit or 8 x 8 bit
   – Four separate interrupt channels for Rx, Tx, error and wake-up
   – Low-pass filter wake-up function
   – In 80QFP, only TxCAN and RxCAN pins are available
   – Loop-back for self test operation
   – Programmable link to a timer input capture channel, for time stamping and network synchronization.
• Enhanced capture timer (ECT)
   – 16-bit main counter with 7-bit prescaler
   – 8 programmable input capture or output compare channels; 4 of the 8 input captures with buffer
   – Input capture filters and buffers, three successive captures on four channels, or two captures on four channels with a capture/compare selectable on the remaining four
   – Four 8-bit or two 16-bit pulse accumulators
   – 16-bit modulus down-counter with 4-bit prescaler
   – Four user-selectable delay counters for signal filtering
• 4 PWM channels with programmable period and duty cycle
   – 8-bit 4-channel or 16-bit 2-channel
   – Separate control for each pulse width and duty cycle
   – Center- or left-aligned outputs
   – Programmable clock select logic with a wide range of frequencies
• Serial interfaces
   – Two asynchronous serial communications interfaces (SCI)
   – MI-Bus implemented on final devices
   – Synchronous serial peripheral interface (SPI)
• LIM (light integration module)
   – WCR (windowed COP watchdog, real time interrupt, clock monitor)
   – ROC (reset and clocks)
   – MEBI (multiplexed external bus interface)
   – MBI (internal bus interface and map)
   – INT (interrupt control)
• Clock generation
   – Phase-locked loop clock frequency multiplier
   – Limp home mode in absence of external clock
   – Slow mode divider
   – Low power 0.5 to 16 MHz crystal oscillator reference clock
   – Option of a Pierce or Colpitts oscillator
• 112-Pin TQFP package or 80-pin QFP package
   – Up to 68 general-purpose I/O lines, plus up to 18 input-only lines in 112TQFP or Up to 48 general-purpose I/O lines, plus up to 10 input-only lines in 80QFP
• 8MHz operation at 5V
• Development support
   – Single-wire background debug™ mode (BDM)
   – On-chip hardware breakpoints