AD7476ARTZ-500RL7 Просмотр технического описания (PDF) - Analog Devices

Номер в каталоге

Компоненты Описание

Список матч

AD7476ARTZ-500RL7

1 MSPS, 12-/10-/8-Bit ADCs in 6-Lead SOT-23

Analog Devices 

AD7476/AD7477/AD7478

TYPICAL CONNECTION DIAGRAM

Figure 14 shows a typical connection diagram for the

AD7476/AD7477/AD7478. VREF is taken internally from VDD

and as such, VDD should be well decoupled. This provides an

analog input range of 0 V to VDD. The conversion result is

output in a 16-bit word with four leading zeros followed by the

MSB of the 12-bit, 10-bit, or 8-bit result. The 10-bit result from

the AD7477 is followed by two trailing zeros. The 8-bit result

from the AD7478 is followed by four trailing zeros.

Alternatively, because the supply current required by the

AD7476/AD7477/AD7478 is so low, a precision reference can

be used as the supply source to the part. A REF19x voltage

reference (REF195 for 5 V or REF193 for 3 V) can be used to

supply the required voltage to the ADC (see Figure 14). This

configuration is especially useful if the power supply is quite

noisy or if the system supply voltages are at some value other

than 5 V or 3 V, such as 15 V.

The REF19x outputs a steady voltage to the AD7476/

AD7477/AD7478. If the low dropout REF193 is used, the

current it typically needs to supply to the AD7476/AD7477/

AD7478 is 1 mA. When the ADC is converting at a rate of

1 MSPS, the REF193 needs to supply a maximum of 1.6 mA to

the AD7476/AD7477/AD7478. The load regulation of the

REF193 is typically 10 ppm/mA (REF193, VS = 5 V), which

results in an error of 16 ppm (48 μV) for the 1.6 mA drawn

from it. This corresponds to a 0.065 LSB error for the AD7476

with VDD = 3 V from the REF193, a 0.016 LSB error for the

AD7477, and a 0.004 LSB error for the AD7478.

For applications where power consumption is of concern, the

power-down mode of the ADC and the sleep mode of the

REF19x reference should be used to improve power perform-

ance. See the Modes of Operation section.

1mA

690nF

1µF

TANT

3V

0.1µF

REF193

10µF

10µF

5V

SUPPLY

0V TO VDD

INPUT

VDD

SCLK

VIN

AD7476/

AD7477/ SDATA

GND AD7478

CS

µC/µP

SERIAL

INTERFACE

Figure 14. REF193 as Power Supply

Table 7 provides some typical performance data with various

references used as a VDD source with a low frequency analog

input. Under the same setup conditions, the references are

compared and the AD780 proved the optimum reference.

Table 7.

Reference Tied to VDD

AD780 @ 3 V

REF193

AD780 @ 2.5 V

REF192

AD1582

AD7476 SNR Performance

1 kHz Input (dB)

71.17

70.4

71.35

70.93

70.05

Analog Input

Figure 15 shows an equivalent circuit of the analog input

structure of the AD7476/AD7477/AD7478. The two diodes, D1

and D2, provide ESD protection for the analog input. Take care

to ensure that the analog input signal never exceeds the supply

rails by more than 300 mV. This causes these diodes to become

forward-biased and start conducting current into the substrate.

These diodes can conduct a maximum of 10 mA without

causing irreversible damage to the part.

The Capacitor C1 in Figure 15 is typically about 4 pF and can

primarily be attributed to pin capacitance. The Resistor R1 is a

lumped component made up of the on resistance of a switch.

This resistor is typically about 100 Ω. The Capacitor C2 is the

ADC sampling capacitor and typically has a capacitance of

30 pF. For ac applications, removing high frequency compo-

nents from the analog input signal is recommended by use of a

band-pass filter on the relevant analog input pin. In applications

where harmonic distortion and signal-to-noise ratio are critical,

the analog input should be driven from a low impedance

source. Large source impedances significantly affect the ac

performance of the ADC. This may necessitate using an input

buffer amplifier. The choice of the op amp is a function of the

particular application.

VDD

C2

D1

R1 30pF

VIN

C1

4pF

D2

CONVERSAION PHASE—SWITCH OPEN

TRACK PHASE—SWITCH CLOSED

Figure 15. Equivalent Analog Input Circuit

When no amplifier is used to drive the analog input, the source

impedance should be limited to low values. The maximum

source impedance depends on the amount of total harmonic

distortion (THD) that can be tolerated. The THD increases as

the source impedance increases and performance degrades.

Figure 16 shows a graph of the total harmonic distortion versus

source impedance for different analog input frequencies when

using a supply voltage of 2.7 V and sampling at a rate of

605 kSPS. Figure 17 and Figure 18 each show a graph of the

total harmonic distortion vs. analog input signal frequency for

various supply voltages while sampling at 993 kSPS with an

SCLK frequency of 20 MHz and 605 kSPS with an SCLK

frequency of 12 MHz, respectively.

Rev. F | Page 14 of 24

Share Link: