SPT9713AIP Просмотр технического описания (PDF) - Cadeka Microcircuits LLC.
Номер в каталоге
Компоненты Описание
производитель
SPT9713AIP Datasheet PDF : 7 Pages
| |||
ELECTRICAL SPECIFICATIONS
TA = TMIN – TMAX, VCC = +5.0 V, VEE = –5.2 V, RSET = 7.5 kΩ, Control Amp In = Ref Out, VOUT = 0 V, unless otherwise specified.
PARAMETERS
TEST
CONDITIONS
TEST
SPT9713A
SPT9713B
LEVEL MIN TYP MAX MIN TYP MAX
Power Supply Requirements
Positive Supply Voltage
IV 4.75 5.0 +5.25 4.75 5.0 +5.25
Negative Supply Voltage
IV –5.46 –5.2 –4.94 –5.46 –5.2 –4.94
Positive Supply Current (+5.0 V) +25 °C
I
8 14
8 14
Full Temp.
VI
16
16
Negative Supply Current (–5.2 V) +25 °C
I
115 140
115 140
Full Temp
VI
148
148
Nominal Power Dissipation
V
640
640
Power Supply Rejection Ratio
±5% of VEE and VCC
I
30 100
30 100
External Ref, +25 °C
Voltage Input and Control
Reference Input Impedance
Ref. Multiplying Bandwidth
Internal Reference Voltage
Internal Reference Voltage Drift
Amplifier Input Impedance
Amplifier Input Bandwidth
+25 °C
+25 °C
Full
+25 °C
+25 °C
V
3
3
V
40
40
VI –1.15 –1.20 –1.25 –1.15 –1.20 –1.25
V
50
50
V
3
3
V
1
1
Digital Inputs
Logic 1 Voltage
Logic 0 Voltage
Logic 1 Current
Logic 0 Current
Input Capacitance
Input Setup Time – tS
Input Setup Time – tS
Input Hold Time – tH
Input Hold Time – tH
Latch Pulse Width – tPWL, tPWH
Full Temp.
Full Temp.
Full Temp.
Full Temp.
+25 °C
+25 °C
Full Temp.
+25 °C
Full Temp.
+25 °C
VI
2.0
2.0
VI
0.8
0.8
VI
20
20
VI
600
600
V
3
3
IV
3
2
3
2
IV
3.5
3.5
IV
0.5 0
0.5 0
IV
0.5
0.5
IV
5.0 4.0
5.0 4.0
UNITS
V
V
mA
mA
mA
mA
mW
µA/V
kΩ
MHz
V
ppm/°C
MΩ
MHz
V
V
µA
µA
pF
ns
ns
ns
ns
ns
TEST LEVEL CODES
All electrical characteristics are subject to the
following conditions:
All parameters having min/max specifications
are guaranteed. The Test Level column indi-
cates the specific device testing actually per-
formed during production and Quality Assur-
ance inspection. Any blank section in the data
column indicates that the specification is not
tested at the specified condition.
LEVEL
I
II
III
IV
V
VI
TEST PROCEDURE
100% production tested at the specified temperature.
100% production tested at TA = +25 °C, and sample tested at the
specified temperatures.
QA sample tested only at the specified temperatures.
Parameter is guaranteed (but not tested) by design and characteri-
zation data.
Parameter is a typical value for information purposes only.
100% production tested at TA = +25 °C. Parameter is guaranteed
over specified temperature range.
SPT9713
3
2/15/01
Share Link: 