MC100SX1230FN Просмотр технического описания (PDF) - Motorola => Freescale
Номер в каталоге
Компоненты Описание
производитель
MC100SX1230FN Datasheet PDF : 8 Pages
| |||
MC100SX1230
ABSOLUTE MAXIMUM RATINGS1
Symbol
Parameter
Value
Unit
VEE
VI
IOUT
Power Supply (VCC = 0V)
Input Voltage (VCC = 0V)
Output Current
–8 to 0
Vdc
0 to –6
Vdc
Continuous
50
mA
Surge
100
TA
Operating Temperature Range
0 to +85
°C
VEE
Operating Range2
–5.7 to 4.2
V
1 Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the
Recommended Operating Conditions.
2 Parametric values specified at: –4.2 to 5.46V
DC CHARACTERISTICS (VCC = VCCO = GND; VEE = –4.2 to 5.46V)
0°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
Condition
VOH
Output HIGH Voltage
–1025 –955 –880 –1025 –955 –880 –1025 –955 –880 mV Vin = VIH(max) or VIL(min)
VOL
Output LOW Voltage
–1810 –1705 –1620 –1810 –1705 –1620 –1810 –1705 –1620 mV Vin = VIH(max) or VIL(min)
VOHA Output HIGH Voltage
–1035
–1035
–1035
mV Vin = VIH(max) or VIL(min)
VOLA
Output LOW Voltage
–1610
–1610
–1610 mV Vin = VIH(max) or VIL(min)
VIH
Input HIGH Voltage
–1165
–880 –1165
–880 –1165
–880 mV
VIL
Input LOW Voltage
–1810
–1475 –1810
–1475 –1810
–1475 mV
VBB
Reference Voltage
–1380
–1260 –1380
–1260 –1380
–1260 V
IIH
Input HIGH Current
200
200
200 µA
IIL
Input LOW Current
0.5
0.5
0.5
µA
IEE
Supply Current
61
122
61
122
70
141 mA
1. 100SX circuits are designed to meet the DC specifications shown in the table after thermal equilibrium has been established. The circuit is mounted in a test socket
or mounted on a printed circuit board and transverse air greater than 500lfm is maintained.
2. All outputs are loaded with 50Ω to VCC – 2V.
AC CHARACTERISTICS (VCC = VCCO = GND; VEE = –4.2 to 5.46V)
0 to 85°C
Symbol
Characteristic
Min Typ Max Unit
Condition
Notes
Fmax
700
MHz
tpd
Propagation CCLKin to CCLKout 650
Delay
CCLKin to QCMI 1000
DCLKin to DCLKout 550
DCLKin to QBIN 1000
CCLKin to DCLKout
CCLKin to QBIN 1100
DCLKin to QCMI 800
1550
1750
1700
1800
2700
1700
ps
LCMI=LBIN=‘L’
LCMI=LBIN=‘L’
Add 3 CCLKin-Cycles to Delay
LCMI=LBIN=‘L’
Add 4 DCLKin-Cycles to Delay
LCMI=‘L’, LBIN=‘H’
LCMI=‘L’, LBIN=‘L’ Add 3 CCLKin-Cycles to Delay
LCMI=‘H’, LBIN=‘L’ Add 5 DCLKin-Cycles to Delay
ts
Setup Time
BINin to CCLKin –375
ps
CMIin to DCLKin 140
th
Hold Time
CCLKin to BINin
DCLKin to CMIin
1000 ps
120
VPP
Minimum Input Swing
250
mV
VCMR Common Mode Range
–0.4
Note
V
tr, tf
Rise/Fall Times
150
700
ps 20% – 80%
1. 100SX circuits are designed to meet the AC specifications shown in the table after thermal equilibrium has been established. The circuit is mounted in a test socket
or mounted on a printed circuit board and transverse air greater than 500lfm is maintained.
2. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range
and the peak-to-peak voltage lies between VPPmin and 1V. The lower end of the CMR range is dependent on VEE and is equal to VEE + 3.0V.
High Performance Frequency
Control Products — BR1334
MOTOROLA
3
Share Link: 