V29C51000T-45J Просмотр технического описания (PDF) - Mosel Vitelic, Corp

Номер в каталоге

Компоненты Описание

Список матч

V29C51000T-45J

512K BIT (65,536 x 8 BIT) 5 VOLT CMOS FLASH MEMORY

Mosel Vitelic, Corp 

MOSEL VITELIC

V29C51000T/V29C51000B

Table 2. Command Codes

Command

Sequence

First Bus

Second Bus

Third Bus

Fourth Bus

Program Cycle Program Cycle Program Cycle Program Cycle

Address Data Address Data Address Data Address Data

Fifth Bus

Six Bus

Program Cycle Program Cycle

Address Data Address Data

Read

XXXXH F0H

Read

5555H AAH 2AAAH 55H 5555H F0H RA

RD

Autoselect

5555H

AAH 2AAAH 55H 5555H

90H 00H

01H

40H

00H(1)

A0H(2)

Byte

Program

5555H AAH 2AAAH 55H 5555H A0H PA

PD(4)

Chip Erase 5555H AAH 2AAAH 55H 5555H 80H 5555H AAH 2AAAH 55H 5555H 10H

Sector Erase 5555H AAH 2AAAH 55H 5555H 80H 5555H AAH 2AAAH 55H PA(3)

30H

NOTES:

1. Top Boot Sector

2. Bottom Boot Sector

3. PA: The address of the memory location to be programmed.

4. PD: The data at the byte address to be programmed.

the device ignores any program attempt into the

device. The internal erase completion can be

determined via DATA polling or toggle bit.

The V29C51000T/V29C51000B is shipped with

pre-erased sectors (all bits = 1).

attempt to read the device will received the

complement of the loaded data on I/O7. Once the

program cycle is completed, I/O7 will show true

data, and the device is then ready for the next

cycle.

Chip Erase Cycle

The V29C51000T/V29C51000B features a chip-

erase operation. The chip erase operation is

initiated by using a specific six-bus-cycle

sequence: two unlock program cycles, a setup

command, two additional unlock program cycles,

and the chip erase command (see Table 2).

The chip erase operation is performed

sequentially, one sector at a time. When the

automated on chip erase algorithm is requested

with the chip erase command sequence, the device

automatically programs and verifies the entire

memory array for an all zero pattern prior to erasure

The automatic erase begins on the rising edge of

the last WE or CE pulse in the command sequence

and terminates when the data on DQ7 is “1”.

Program Cycle Status Detection

There are two methods for determining the state

of the V29C51000T/V29C51000B during a

program (erase/program) cycle: DATA Polling

(I/O7) and Toggle Bit (I/O6).

DATA Polling (I/O7)

The V29C51000T/V29C51000B features DATA

polling to indicate the end of a program cycle.

When the device is in the program cycle, any

Toggle Bit (I/O6)

The V29C51000T/V29C51000B also features

another method for determining the end of a

program cycle. When the device is in the program

cycle, any attempt to read the device will result in

l/O6 toggling between 1 and 0. Once the program is

completed, the toggling will stop. The device is then

ready for the next operation. Examining the toggle

bit may begin at any time during a program cycle.

Boot Block Protection

The V29C51000T/V29C51000B features

hardware Boot Block Protection. This feature will

prevent erasing/programming of data in the Boot

Block once the feature is enabled (see Table 3).

The device is shipped with the Boot Block

unprotected.

Autoselect

The V29C51000T/V29C51000B features an

Autoselect mode to identify the Boot Block

(protected/unprotected), the Device (Top/Bottom),

and the manufacturer ID.

To get to the Autoselect mode, a high voltage

(VH) must be applied to the A9 pin. Once the A9

signal is returned to LOW or HIGH, the device will

return to the previous mode.

V29C51000T/V29C51000B Rev. 0.5 October 2000

10

Share Link: