MH16V64AWJ-5 Просмотр технического описания (PDF) - MITSUBISHI ELECTRIC
Номер в каталоге
Компоненты Описание
Список матч
MH16V64AWJ-5
MITSUBISHI ELECTRIC
MH16V64AWJ-5 Datasheet PDF : 20 Pages
| |||
Preliminary Spec.
Specifications subject to
change without notice.
MITSUBISHI LSIs
MH16V64AWJ -5, -6
FAST PAGE MODE 1073741824 - BIT ( 16777216 - WORD BY 64 - BIT ) DYNAMIC RAM
SWITCHING CHARACTERISTICS (Ta=0~70°C, Vcc=3.3V±0.3V, Vss=0V, unless otherwise noted , see notes 6,13,14)
Limits
Symbol
Parameter
-5
-6
Unit
Min
Max
Min
Max
tCAC Access time from /CAS
(Note 7,8)
13
15
ns
tRAC Access time from /RAS
(Note 7,9)
50
60
ns
tAA
Column address access time
(Note 7,10)
25
30
ns
tCPA Access time from /CAS precharge
(Note 7,11)
30
35
ns
tOEA Access time from /OE
(Note 7)
13
15
ns
tCLZ
Output low impedance time /CAS low
(Note 7)
5
tOEZ Output disable time after /OE high
(Note 12)
13
tOFF Output disable time after /CAS high
(Note 12)
13
5
ns
15
ns
15
ns
Note 6: An initial pause of 500us is required after power-up followed by a minimum of eight initialization cycles (any combination of cycles
containing /CAS before /RAS refresh).
Note the /RAS may be cycled during the initial pause . And any 8 /RAS or /RAS /CAS cycles are required after prolonged periods
(greater than 64 ms) of /RAS inactivity before proper device operation is achieved.
7: Measured with a load circuit equivalent to 1 TTL load and 100pF,VOH=2.4V(IOH=-2mA) and VOL=0.4V(IOL=-2mA).
The reference levels for measuring of output signals are 2.0V(VOH)and 0.8V(VOL).
8: Assumes that tRCD ≥ tRCD(max), tASC ≥ tASC(max) and tCP ≥ tCP(max).
9: Assumes that tRCD ≤ tRCD(max) and tRAD ≤ tRAD(max). If tRCD or tRAD is greater than the maximum recommended value shown in this table,
tRAC will increase by amount that tRCD exceeds the value shown.
10: Assumes that tRAD ≥ tRAD(max) and tASC ≤ tASC(max).
11: Assumes that tCP ≤ tCP(max) and tASC ≥ tASC(max).
12: tOEZ (max) and tOFF(max) defines the time at which the output achieves the high impedance state (IOUT ≤ I ± 10uA I ) and is not reference to
VOH(min) or VOL(max).
TIMING REQUIREMENTS (For Read, Write, Read-Modify-Write ,Refresh, and Fast-Page Mode Cycles)
(Ta=0~70°C, Vcc=3.3V±0.3V, Vss=0V, unless otherwise noted ,see notes 13,14)
Limits
Symbol
Parameter
-5
-6
Unit
Min
Max
Min
Max
tREF
tRP
tRCD
Refresh cycle time
/RAS high pulse width
Delay time, /RAS low to /CAS low
30
(Note15) 18
64
40
37
20
64
ms
ns
45
ns
tCRP Delay time, /CAS high to /RAS low
5
10
ns
tRPC
tCPN
Delay time, /RAS high to /CAS low
/CAS high pulse width
0
0
ns
10
10
ns
tRAD Column address delay time from /RAS low (Note16) 13
25
15
30
ns
tASR Row address setup time before /RAS low
0
tASC Column address setup time before /CAS low(Note17)
0
0
ns
5
0
10
ns
tRAH Row address hold time after /RAS low
8
10
ns
tCAH Column address hold time after /CAS low
13
15
ns
tDZC Delay time, data to /CAS low
(Note18)
0
0
ns
tDZO Delay time, data to /OE low
(Note18)
0
0
ns
tCDD Delay time, /CAS high to data
(Note19) 13
15
ns
tODD
tT
Delay time, /OE high to data
Transition time
(Note19) 13
15
ns
(Note20)
1
50
1
50
ns
Note 13: The timing requirements are assumed tT =5ns.
14: VIH(min) and VIL(max) are reference levels for measuring timing of input signals.VIH(min) and VIL(max) of the switching characteristics are
2.0V and 0.8V respectively.
15: tRCD(max) is specified as a reference point only. If tRCD is less than tRCD(max), access time is tRAC. If tRCD is greater than tRCD(max), access
time is controlled exclusively by tCAC or tAA. .
16: tRAD(max) is specified as a reference point only. If tRAD≥tRAD(max) and tASC≤tASC(max), access time is controlled exclusively by tAA.
17: tASC(max) is specified as a reference point only. If tRCD≥tRCD(max) and tASC≥tASC(max), access time is controlled exclusively by tCAC.
18: Either tDZC or tDZO must be satisfied.
19: Either tCDD or tODD must be satisfied.
20: tT is measured between VIH(min) and VIL(max).
MIT-DS-0108-0.5
MITSUBISHI
ELECTRIC
( 7 / 20 )
26/Feb./1997
Share Link: