MC100EL56 Просмотр технического описания (PDF) - ON Semiconductor
Номер в каталоге
Компоненты Описание
Список матч
MC100EL56 Datasheet PDF : 6 Pages
| |||
MC100EL56
Table 4. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
VCC
PECL Mode Power Supply
VEE
NECL Mode Power Supply
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
Iout
Output Current
VEE = 0 V
VCC = 0 V
VEE = 0 V
VCC = 0 V
Continuous
Surge
VI ≤ VCC
VI ≥ VEE
8
V
−8
V
6
V
−6
V
50
mA
100
mA
IBB
VBB Sink/Source
TA
Operating Temperature Range
Tstg
Storage Temperature Range
qJA
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
SO−20 WB
SO−20 WB
± 0.5
−40 to +85
−65 to +150
90
60
mA
°C
°C
°C/W
°C/W
qJC
Thermal Resistance (Junction−to−Case)
Standard Board
SO−20 WB
Tsol
Wave Solder
Pb <2 to 3 sec @ 248°C
Pb−Free <2 to 3 sec @ 260°C
30 to 35
265
265
°C/W
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 5. 100EL SERIES PECL DC CHARACTERISTICS VCC = 5.0 V; VEE = 0.0 V (Note 2)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
Power Supply Current
20
24
20
24
20
24 mA
VOH
Output HIGH Voltage (Note 3)
3915 3995 4120 3975 4045 4120 3975 4050 4120 mV
VOL
Output LOW Voltage (Note 3)
3170 3305 3445 3190 3295 3380 3190 3295 3380 mV
VIH
Input HIGH Voltage (Single−Ended)
3835
4120 3835
4120 3835
4120 mV
VIL
Input LOW Voltage (Single−Ended)
3190
3525 3190
3525 3190
3525 mV
VBB
Output Voltage Reference
3.62
3.74 3.62
3.74 3.62
3.74 V
VIHCMR Common Mode Range
(Differential Configuration) (Note 4)
VPP t 500 mV 1.3
VPP w 500 mV 1.5
4.6 1.2
4.6 1.4
4.6 1.2
4.6 1.4
V
4.6
4.6
IIH
Input HIGH Current
150
150
150 mA
IIL
Input LOW Current
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
2. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / −0.5 V.
3. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
4. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin
and 1 V.
http://onsemi.com
3
Share Link: 