IDT74FST1616209PV Просмотр технического описания (PDF) - Integrated Device Technology

Номер в каталоге

Компоненты Описание

Список матч

IDT74FST1616209PV

9-BIT BUS EXCHANGE SWITCH

Integrated Device Technology 

IDT74FST163209

9-BIT BUS EXCHANGE SWITCH

COMMERCIAL TEMPERATURE RANGE

POWER SUPPLY CHARACTERISTICS

Symbol

∆ICC

ICCD

IC

Parameter

Quiescent Power Supply Current

TTL Inputs HIGH

Dynamic Power Supply

Current(4)

Total Power Supply Current(6)

Test Conditions(1)

VCC = Max.

VIN = 3.4V(3)

VCC = Max.

VIN = VCC

Outputs Open

VIN = GND

Enable Pin Toggling

50% Duty Cycle

VCC = Max.

VIN = VCC

Outputs Open

VIN = GND

3 Select Pins Toggling

Min. Typ.(2) Max. Unit

— 0.5 1.5 mA

—

30

40 µA/

MHz/

Switch

— 2.7 3.6 mA

(9 Switches Toggling)

fi = 10MHz

50% Duty Cycle

VIN = 3.4

VIN = GND

— 3.5 5.9

NOTES:

1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.

2. Typical values are at VCC = 5.0V, +25°C ambient.

3. Per TTL driven input (VIN = 3.4V). All other inputs at VCC or GND.

4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations.

5. Values for these conditions are examples of the ICC formula. These limits are guaranteed but not tested.

6. IC = IQUIESCENT + IINPUTS + IDYNAMIC

IC = ICC + ∆ICC DHNT + ICCD (fiN)

ICC = Quiescent Current

∆ICC = Power Supply Current for a TTL High Input (VIN = 3.4V)

DH = Duty Cycle for TTL Inputs High

NT = Number of TTL Inputs at DH

ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL)

fi = Input Frequency

N = Number of Switches Toggling at fi

All currents are in milliamps and all frequencies are in megahertz.

3510 tbl 06

SWITCHING CHARACTERISTICS OVER OPERATING RANGE

Following Conditions Apply Unless Otherwise Specified:

Commercial: TA = –40°C to +85°C, VCC = 5.0V ±10%

Symbol

Description

Condition(1)

Min.(2)

Typ.

Max.

Unit

tPLH Data Propagation Delay

tPHL

A to B, B to A(3,4)

CL = 50pF

—

RL = 500Ω

—

0.25

ns

tBX

Switch Multiplex Delay

S to A, B

1.5

—

6.5

ns

tPZH Switch Turn on Delay

tPZL

S to A, B

1.5

—

6.5

ns

tPHZ

tPLZ

|QCI|

Switch Turn off Delay

S to A, B

Charge Injection, Typical(5,7)

1.5

—

7

ns

—

1.5

—

pC

|QDCI| Charge Injection, Typical(6,7)

—

0.5

—

NOTES:

3510 tbl 07

1. See test circuit and waveforms.

2. Minimum limits guaranteed but not tested.

3. This parameter is guaranteed by design but not tested.

4. The bus switch contributes no propagation delay other than the RC delay of the on resistance of the switch and the load capacitance. The time constant

for the switch alone is of the order of 2.5ns for 50pF load. Since this time is constant and much smaller than the rise/fall times of typical driving signals,

it adds very little propagation delay to the system. Propagation delay on the bus switch when used in a system is determined by the driving circuit on the

driving side of the switch and its interaction with the load on the driven side.

5. Measured at switch turn off, load = 50 pF in parallel with 10 MΩ scope probe, VIN = 0.0 volts.

6. Measured at switch turn off through bus multiplexer, (e.g.- A1 to B1 = >A1 to B2), load = 50 pF in parallel with 10 MΩ scope probe, VIN at A = 0.0 volts. Charge

injection is reduced because the injection from the turn off of the A to C switch is compensated by the turn on of the B to C switch.

7. Characterized parameter. Not 100% tested.

4

Share Link: