MT8926 Просмотр технического описания (PDF) - Mitel Networks
Номер в каталоге
Компоненты Описание
производитель
MT8926 Datasheet PDF : 26 Pages
| |||
MT8926
VSS 1
ECLK 2
RxA 3
RxB 4
IC 5
E8Ki 6
E8Ko 7
VSS 8
CSTo 9
CSTi0 10
CSTi1 11
F0i 12
C2i 13
VSS 14
28 VDD
27 IC
26 DSTi1
25 DSTi0
24 DSTo
23 IC
22 VSS
21 IC
20 IRQ
19 1SEC
18 FDLo
17 FLDi
16 RESET
15 VDD
IC
E8Ki
E8Ko
VSS
CSTo
CSTi0
CSTi1
4 3 2 1 28 27 26
5
25
6
24
7
23
8
22
9
21
10
20
11
19
12 13 14 15 16 17 18
DSTi0
DSTo
IC
VSS
IC
IRQ
1SEC
28 PIN PLASTIC DIP
28 PIN PLASTIC J-LEAD
Pin Description
Figure 2 - Pin Connections
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
Name
VSS
ECLK
RxA
RxB
IC
E8Ki
E8Ko
VSS
CSTo
CSTi0
CSTi1
F0i
Description
System Ground.
Extracted Clock Input. A 1.544 MHz clock derived from the received data. This signal is
used to clock in the data on pins RxA and RxB.
See Figure 11 for timing information.
Receive A Input. A unipolar active low signal decoded from the received T1 signal. See
Figure 11 for timing information.
Receive B Input. A unipolar active low signal decoded from the received T1 signal. See
Figure 11 for timing information.
Internal Connection. Must be tied to VSS for normal operation.
Extracted 8 kHz Input. A low going pulse on this input is used by the PMAC to locate the
framing bit in the received signal. The device uses this information to detect errors in the
received framing bits. Connect to E8Ko of the MT8976/77. See Figure 12 for timing
information.
8 kHz clock output. The 8 kHz signal input at E8Ki is output on this pin when bit 2 (8KEn)
of the PMAC Control Word is set. The output is pulled high when 8KEn is reset. See
Figure 12 for timing information.
System Ground.
Control ST-BUS Output. The data that enters the PMAC on CSTi0 will exit the device on
this pin. Data derived by the PMAC will be inserted into specific channels of this output
stream. See Figures 13 and 14 for timing information and Figure 5 for channel allocation.
Control ST-BUS Input 0. Accepts the serial ST-BUS stream output on CSTo of the
MT8976/77. The data that enters the PMAC on this pin exits the device on CSTo. The
contents of specific CSTi0 channels is replaced by data derived by the PMAC. See Figures
13 and 14 for timing information and Figure 4 for channel allocation.
Control ST-BUS Input 1. Channel 11 of this ST-BUS input stream is used to control
specific features in the device (Table 14). Channel 7 is used for the transmit bit-oriented
message (Table 13), and channel 15 is used to control loopback functions (Table 4). See
Figure 13 for timing information and Figure 3 for channel allocation.
Frame Pulse Input. This input accepts an 8 kHz signal, which is used to delineate the ST-
BUS frame boundary. See Figure 15 for timing information.
4-4
Share Link: 