MCM67M618AFN10 Просмотр технического описания (PDF) - Motorola => Freescale
Номер в каталоге
Компоненты Описание
Список матч
MCM67M618AFN10 Datasheet PDF : 12 Pages
| |||
AC OPERATING CONDITIONS AND CHARACTERISTICS
(VCC = 5.0 V ± 5%, TA = 0 to + 70°C, Unless Otherwise Noted)
Input Timing Measurement Reference Level . . . . . . . . . . . . . . . 1.5 V
Input Pulse Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 3.0 V
Input Rise/Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ns
Output Timing Reference Level . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 V
Output Load . . . . . . . . . . . . See Figure 1A Unless Otherwise Noted
READ/WRITE CYCLE TIMING (See Notes 1, 3, and 4)
MCM67M618A–9 MCM67M618A–10 MCM67M618A–12
Parameter
Symbol Min
Max
Min
Max
Min
Max
Unit Notes
Cycle Time
tKHKH
15
—
16.6
—
20
—
ns
Clock Access Time
tKHQV
—
9
—
10
—
12
ns
5
Output Enable to Output Valid
tGLQV
—
5
—
5
—
6
ns
Clock High to Output Active
tKHQX1
6
—
6
—
6
—
ns
Clock High to Output Change
tKHQX2
3
—
3
—
3
—
ns
Output Enable to Output Active
tGLQX
0
—
0
—
0
—
ns
Output Disable to Q High–Z
tGHQZ
—
6
—
7
—
7
ns
6
Clock High to Q High–Z
tKHQZ
3
6
3
7
3
7
ns
6
Clock High Pulse Width
tKHKL
5
—
5
—
6
—
ns
Clock Low Pulse Width
tKLKH
5
—
5
—
6
—
ns
Setup Times:
Address tAVKH
2.5
—
2.5
—
2.5
—
ns
7
Address Status tTSVKH
Data In tDVKH
Write tWVKH
Address Advance tBAVKH
Chip Enable tEVKH
Hold Times:
Address tKHAX
0.5
—
0.5
—
0.5
—
ns
7
Address Status tKHTSX
Data In tKHDX
Write tKHWX
Address Advance tKHBAX
Chip Enable tKHEX
NOTES:
1. In setup and hold times, W (write) refers to either one or both byte write enables LW and UW.
2. A read cycle is defined by UW and LW high or TSP low for the setup and hold times. A write cycle is defined by LW or UW low and TSP high
for the setup and hold times.
3. All read and write cycle timings are referenced from K or G.
4. G is a don’t care when UW or LW is sampled low.
5. Maximum access times are guaranteed for all possible MC68040 and PowerPC external bus cycles.
6. Transition is measured ± 500 mV from steady–state voltage with load of Figure 1B. This parameter is sampled rather than 100% tested. At
any given voltage and temperature, tKHQZ max is less than tKHQZ1 min for a given device and from device to device.
7. This is a synchronous device. All addresses must meet the specified setup and hold times for ALL rising edges of K whenever TSP or TSC
is low, and the chip is selected. All other synchronous inputs must meet the specified setup and hold times for ALL rising edges of K when
the chip is enabled. Chip enable must be valid at each rising edge of clock for the device (when TSP or TSC is low) to remain enabled.
OUTPUT
AC TEST LOADS
Z0 = 50 Ω
RL = 50 Ω
VL = 1.5 V
OUTPUT
255 Ω
+5V
480 Ω
5 pF
Figure 1A
Figure 1B
MOTOROLA FAST SRAM
MCM67M618A
5
Share Link: 