IDT29FCT2521CT Просмотр технического описания (PDF) - Integrated Device Technology
Номер в каталоге
Компоненты Описание
Список матч
IDT29FCT2521CT Datasheet PDF : 7 Pages
| |||
IDT29FCT520AT/BT/CT/DT, 521AT/BT/CT/DT
MULTILEVEL PIPELINE REGISTERS
MILITARY AND COMMERCIAL TEMPERATURE RANGES
ABSOLUTE MAXIMUM RATINGS(1)
Symbol
Rating
VTERM(2) Terminal Voltage
with Respect to
GND
VTERM(3) Terminal Voltage
with Respect to
GND
TA
Operating
Temperature
TBIAS Temperature
Under Bias
TSTG Storage
Temperature
PT
Power Dissipation
Commercial
–0.5 to +7.0
–0.5 to
VCC +0.5
0 to +70
–55 to +125
–55 to +125
0.5
Military
–0.5 to +7.0
–0.5 to
VCC +0.5
–55 to +125
–65 to +135
–65 to +150
0.5
Unit
V
V
°C
°C
°C
W
IOUT
DC Output
–60 to +120 –60 to +120 mA
Current
NOTES:
2619 lnk 03
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RAT-
INGS may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions
above those indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating conditions for
extended periods may affect reliability. No terminal voltage may exceed
VCC by +0.5V unless otherwise noted.
2. Input and VCC terminals only.
3. Outputs and I/O terminals only.
CAPACITANCE (TA = +25°C, f = 1.0MHz)
Symbol Parameter(1) Conditions Typ. Max. Unit
CIN
Input
Capacitance
VIN = 0V
6
10 pF
COUT Output
VOUT = 0V 8
12 pF
Capacitance
NOTE:
2619 lnk 04
1. This parameter is measured at characterization but not tested.
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Commercial: TA = 0°C to +70°C, VCC = 5.0V ± 5%; Military: TA = –55°C to +125°C, VCC = 5.0V ± 10%
Symbol
Parameter
Test Conditions(1)
Min. Typ.(2) Max. Unit
VIH
Input HIGH Level
Guaranteed Logic HIGH Level
2.0
—
—
V
VIL
IIH
IIL
IOZH
Input LOW Level
Input HIGH Current(4)
Input LOW Current(4)
High Impedance(4)
Guaranteed Logic LOW Level
VCC = Max.
VI = 2.7V
VCC = Max.
VI = 0.5V
VCC = Max.
VO = 2.7V
—
—
0.8
V
—
—
±1
µA
—
—
±1
µA
—
—
±1
µA
IOZL
Output Current
VO = 0.5V
II
Input HIGH Current(4)
VCC = Max., VI = VCC (Max.)
—
—
±1
—
—
±1
µA
VIK
Clamp Diode Voltage
VCC = Min., IN = –18mA
IOS
Short Circuit Current
VCC = Max.(3), VO = GND
—
–0.7 –1.2
V
–60
–120 –225 mA
VOH
Output HIGH Voltage
VCC = Min.
IOH = –6mA MIL.
2.4
3.3
—
V
VIN = VIH or VIL
IOH = –8mA COM’L.
IOH = –12mA MIL.
2.0
3.0
—
IOH = –15mA COM’L.
VOL
Output LOW Voltage
VCC = Min.
IOL = 32mA MIL.
—
0.3
0.5
V
VIN = VIH or VIL
IOL = 48mA COM’L.
VH
Input Hysteresis
—
—
200
—
mV
ICC
Quiescent Power
Supply Current
VCC = Max.
VIN = GND or VCC
—
0.01
1
mA
NOTES:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, +25°C ambient.
3. Not more than one output should be shorted at one time. Duration of the short circuit test should not exceed one second.
4. The test limit for this parameter is ±5µA at TA = -55°C.
2619 tbl 05
6.2
3
Share Link: 