PI5C33X257B(1997) Просмотр технического описания (PDF) - Pericom Semiconductor
Номер в каталоге
Компоненты Описание
Список матч
PI5C33X257B Datasheet PDF : 3 Pages
| |||
PI5C33X257
123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012122434:5162789M012U34X56/7D89E01M234U567X890B12u1s23S4w567i8t9c0h12
Product Pin Description
Pin Name
IAn-ILn
S
En
YA-YL
GND
VCC
NC
Description
Data Inputs
Select Inputs
Enable
Data Outputs
Ground
Power
No Connect
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ............................................................ –65°C to +150°C
Ambient Temperature with Power Applied ........................... –40°C to +85°C
Supply Voltage to Ground Potential (Inputs & Vcc Only) .... –0.5V to +7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only) –0.5V to +7.0V
DC Input Voltage .................................................................. –0.5V to +7.0V
DC Output Current ............................................................................ 120 mA
Power Dissipation ................................................................................... 0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device.
This is a stress rating only and functional operation of
the device at these or any other conditions above
those indicated in the operational sections of this
specification is not implied. Exposure to absolute
maximum rating conditions for extended periods
may affect reliability.
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5V ±5%)
Parameters Description
Test Conditions(1)
Min. Typ(2)
VIH
Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0
VIL
Input LOW Voltage
Guaranteed Logic LOW Level
–0.5
IIH
Input HIGH Current
VCC = Max., VIN = VCC
IIL
Input LOW Current
VCC = Max., VIN = GND
IOZH
High Impedance Output Current 0 ≤ I, Y ≤ VCC
VIK
Clamp Diode Voltage
VCC = Min., IIN = –18 mA
–0.7
IOS
Short Circuit Current(3)
I (Y) = 0V, Y (I) = VCC
100
VH
Input Hysteresis at Control Pins
150
RON
Switch On Resistance(4)
VCC = Min., VIN = 0.0V, ION = 48 mA
5
VCC = Min., VIN = 2.4V, ION = 15 mA
10
Max.
0.8
±1
±1
±1
–1.2
7
15
Units
V
V
µA
µA
µA
V
mA
mV
Ω
Capacitance (TA = 25°C, f = 1 MHz)
Parameters(5)
Description
Test Conditions
Typ Max. Units
CIN
COFF
CON
Input Capacitance
In/Yn Capacitance, Switch Off
In/Yn Capacitance, Switch On
VIN = 0V
VIN = 0V
VIN = 0V
6
pF
6
pF
14
pF
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at Vcc = 5.0V, TA = 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between I and Y pin at indicated current through the switch. ON resistance is determined by the
lower of the voltages on the two (I,Y) pins.
5. This parameter is determined by device characterization but is not production tested.
189
PS8114 04/24/97
Share Link: 