MAX127ACAI Просмотр технического описания (PDF) - Maxim Integrated

Номер в каталоге

Компоненты Описание

производитель

MAX127ACAI

Multirange, +5V, 12-Bit DAS with 2-Wire Serial Interface

Maxim Integrated 

Multirange, +5V, 12-Bit DAS with

2-Wire Serial Interface

SLAVE ADDRESS BYTE

01

MSB

RA

LSB

1

2

789

START

CONDITION

MSB DATA BYTE

D11

MSB

10 11

D4 A

D3

LSB

MSB

17 18 19

LSB DATA BYTE

FILLED WITH

4 ZEROS

D0

A

LSB

22 23

26 27

STOP

CONDITION

Figure 10. Complete 2-Wire Serial Read Transmission

The MAX127/MAX128 ignore acknowledge and NOT-

acknowledge conditions issued by the master during

the read cycle. The device waits for the master to read

the output data or waits until a STOP condition is

issued. Figure 10 shows a complete read cycle.

In unipolar input mode, the output is straight binary. For

bipolar input mode, the output is two’s complement. For

output binary codes see the Transfer Function section.

Applications Information

Power-On Reset

The MAX127/MAX128 power up in normal operating

mode, waiting for a START condition followed by the

appropriate slave address. The contents of the input

and output data registers are cleared at power-up.

Internal or External Reference

The MAX127/MAX128 operate with either an internal or

an external reference (Figures 11a–11c). An external

reference is connected to either REF or to REFADJ.

The REFADJ internal buffer gain is trimmed to 1.6384 to

provide 4.096V at REF from a 2.5V reference.

Internal Reference

The internally trimmed 2.50V reference is amplified

through the REFADJ buffer to provide 4.096V at REF.

Bypass REF with a 4.7µF capacitor to AGND and bypass

REFADJ with a 0.01µF capacitor to AGND (Figure 11a).

The internal reference voltage is adjustable to ±1.5%

(±65 LSBs) with the reference-adjust circuit of Figure 12.

External Reference

To use the REF input directly, disable the internal buffer

by connecting REFADJ to VDD (Figure 11b). Using the

REFADJ input eliminates the need to buffer the refer-

ence externally. When the reference is applied at

REFADJ, bypass REFADJ with a 0.01µF capacitor to

AGND (Figure 11c).

At REF and REFADJ, the input impedance is a mini-

mum of 10kΩ for DC currents. During conversions, an

external reference at REF must be able to drive a

400µA DC load, and must have an output impedance

of 10Ω or less. If the reference has higher input imped-

ance or is noisy, bypass REF with a 4.7µF capacitor to

AGND as close to the chip as possible.

With an external reference voltage of less than 4.096V

at REF or less than 2.5V at REFADJ, the increase in

RMS noise to the LSB value (full-scale voltage/4096)

results in performance degradation and loss of effec-

tive bits.

Power-Down Mode

To save power, put the converter into low-current shut-

down mode between conversions. Two programmable

power-down modes are available, in addition to the

hardware shutdown. Select STBYPD or FULLPD by pro-

gramming PD0 and PD1 in the input control byte (Table

4). When software power-down is asserted, it becomes

effective only after the end of conversion. In all power-

down modes, the interface remains active and conver-

sion results may be read. Input overvoltage protection

is active in all power-down modes.

______________________________________________________________________________________ 13

Share Link: