CS5525-BP Просмотр технического описания (PDF) - Cirrus Logic

Номер в каталоге

Компоненты Описание

Список матч

CS5525-BP

16-Bit/20-Bit Multi-Range ADC with 4-Bit Latch

Cirrus Logic 

CS5525 CS5526

CS5525 16-Bit Output Coding

CS5526 20-Bit Output Coding

Unipolar Input Offset

Voltage Binary

>(VFS-1.5 LSB) FFFF

VFS-1.5 LSB

FFFF

-----

FFFE

8000

VFS/2-0.5 LSB -----

7FFF

+0.5 LSB

0001

-----

0000

<(+0.5 LSB) 0000

Bipolar Input

Voltage

>(VFS-1.5 LSB)

VFS-1.5 LSB

-0.5 LSB

-VFS+0.5 LSB

<(-VFS+0.5 LSB)

Two's

Complement

7FFF

7FFF

-----

7FFE

0000

-----

FFFF

8001

-----

8000

8000

Unipolar Input Offset Bipolar Input

Two's

Voltage Binary

Voltage

Complement

>(VFS-1.5 LSB) FFFFF >(VFS-1.5 LSB)

7FFFF

VFS-1.5 LSB

FFFFF

-----

FFFFE

VFS-1.5 LSB

7FFFF

-----

7FFFE

80000

VFS/2-0.5 LSB -----

7FFFF

-0.5 LSB

00000

-----

FFFFF

+0.5 LSB

00001

-----

00000

-VFS+0.5 LSB

80001

-----

80000

<(+0.5 LSB) 00000 <(-VFS+0.5 LSB)

80000

Note: VFS in the table equals the voltage between ground and full scale for any of the unipolar gain ranges, or the

voltage between ± full scale for any of the bipolar gain ranges. See text about error flags under overrange

conditions.

Table 6. 5525/26 Output Coding

to the converters is extremely overranged. If the OD

bit is set, the conversion data bits can be completely

erroneous. The OD flag bit will be cleared to logic 0

when the modulator becomes stable. Table 6 illus-

trates the output coding for the CS5525/26.

Power Consumption

The CS5525/26 accommodate four power con-

sumption modes: normal, low power, standby, and

sleep. The normal mode, the default mode, is en-

tered after a power-on-reset and typically con-

sumes 9.4 mW. The low power mode is an alternate

mode that reduces the consumed power to 4.9 mW.

It is entered by setting bit D16 (the low power

mode bit) in the configuration register to logic 1.

Since the converter’s noise performance improves

with increased power consumption, slightly de-

graded noise or linearity performance should be ex-

pected in the low power mode. The final two modes

are referred to as the power save modes. They pow-

er down most of the analog portion of the chips and

stop filter convolutions. The power save modes are

entered whenever the PS/R bit and the CB bit of the

command word are set to logic 1. The particular

power save mode entered depends on state of bit

D4 (the Power Save Select bit) in the configuration

register. If D4 is logic 0, the converters enters the

standby mode reducing the power consumption to

1.2mW. The standby mode leaves the oscillator

and the on-chip bias generator running. This allows

the converters to quickly return to the normal or

low power mode once the PS/R bit is set back to a

logic 1. If D4 in the configuration register and CB

and PS/R in the command word are set to logic 1,

the sleep mode is entered reducing the consumed

power to less than 500 µW. Since the sleep mode

disables the oscillator, approximately a 500ms os-

cillator start-up delay period is required before re-

turning to the normal or low power mode.

PCB Layout

The CS5525/26 should be placed entirely over an

analog ground plane with both the AGND and

DGND pins of the device connected to the analog

plane. Place the analog-digital plane split immedi-

ately adjacent to the digital portion of the chip.

DS202F3

23

Share Link: