RP1-1.5V(2012) Просмотр технического описания (PDF) - Panasonic Corporation
Номер в каталоге
Компоненты Описание
Список матч
RP1-1.5V Datasheet PDF : 5 Pages
| |||
Discontinued as of August 31, 2012
NOTES
1. Coil operating power
Pure DC current should be applied to the
coil. The wave form should be
rectangular. If it includes ripple, the ripple
factor should be less than 5%.
However, check it with the actual circuit
since the characteristics may be slightly
different. The nominal operating voltage
should be applied to the coil for more
than 20 ms to set/reset the latching type
relay.
2. Coil connection
When connecting coils, refer to the wiring
diagram to prevent mis-operation or
malfunction.
3. External magnetic field
Since RP relays are highly sensitive
polarized relays, their characteristics will
be affected by a strong external magnetic
field. Avoid using the relay under that
condition.
4. Packing direction
Relays are packed in a tube with the
orientation stripe (PIN NO. 1) toward the
green stopper.
Stopper (gray)
Stopper (green)
Orientation (indicates PIN No.1) stripe
5. Automatic mounting
To maintain the internal function of the
relay, the chucking pressure should
not exceed the values below.
Chucking pressure* in the direction A:
4.9 N {500 gf} or less
Chucking pressure* in the direction B:
9.8 N {1 kgf} or less
Chucking pressure* in the direction C:
9.8 N {1 kgf} or less
Please chuck the portion.
Avoid chucking the center of the relay. In
addition, excessive chucking pressure to
the pinpoint of the relay should be
avoided.
A (4) C
(5)
(6)
B
mm inch
• Direction A • Direction B • Direction C
654 3
.118
6
123
.236
123
*Value of chucking pressure is shown by the value of weight
pressed on the portion (4 mm .157 inch dia.).
6. Soldering
Preheat according to the following
conditions.
Temperature
120°C 248°F or less
Time
Within 2 minute
Soldering should be done at 260±5°C
500±9°F within 6 s.
1) Perform manual soldering under the
conditions below.
• Within 10 s at 260°C 500°F
• Within 3 s at 350°C 662°F
7. Conditions for operation, transport
and storage conditions
1) Ambient temperature, humidity, and
atmospheric pressure during usage,
transport, and storage of the relay:
(1) Temperature:
–40 to +70°C –40 to +158°F
(2) Humidity: 5 to 85% RH
(Avoid freezing and condensation.)
The humidity range varies with the
temperature. Use within the range
indicated in the graph below.
(3) Atmospheric pressure: 86 to 106 kPa
Temperature and humidity range for
RP
usage, transport, and storage:
Humidity, %R.H.
85
Tolerance range
(Avoid freezing
when used at
temperatures
lower than
0°C 32°F)
5
(Avoid
condensation
when used at
temperatures
higher than
0°C 32°F)
-30
0
70
-22
32
158
Temperature, °C °F
2) Condensation
Condensation forms when there is a
sudden change in temperature under
high temperature and high humidity
conditions. Condensation will cause
deterioration of the relay insulation.
3) Freezing
Condensation or other moisture may
freeze on the relay when the temperature
is lower than 0°C 32°F. This causes
problems such as sticking of movable
parts or operational time lags.
4) Low temperature, low humidity
environments
The plastic becomes brittle if the relay is
exposed to a low temperature, low
humidity environment for long periods of
time.
For Cautions for Use, see Relay Technical Information.
ds_61306_en_rp: 011111D
5
Share Link: 