HS-80C86RH(1995) Просмотр технического описания (PDF) - Intersil
Номер в каталоге
Компоненты Описание
Список матч
HS-80C86RH Datasheet PDF : 37 Pages
| |||
HS-80C86RH
Ceramic Metal Seal Flatpack Packages (Flatpack)
E
1
e
b
E1
L
Q
A
E2
c1 LEAD FINISH
N
A
A
D
S1
C
BASE
METAL
(c)
b1
M
M
(b)
SECTION A-A
NOTES:
1. Index area: A notch or a pin one identification mark shall be locat-
ed adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used
as a pin one identification mark. Alternately, a tab (dimension k)
may be used to identify pin one.
2. If a pin one identification mark is used in addition to a tab, the lim-
its of dimension k do not apply.
3. This dimension allows for off-center lid, meniscus, and glass
overrun.
4. Dimensions b1 and c1 apply to lead base metal only. Dimension
M applies to lead plating and finish thickness. The maximum lim-
its of lead dimensions b and c or M shall be measured at the cen-
troid of the finished lead surfaces, when solder dip or tin plate
lead finish is applied.
5. N is the maximum number of terminal positions.
K42.A TOP BRAZED
42 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE
SYMBOL
INCHES
MIN
MAX
MILLIMETERS
MIN
MAX
NOTES
A
-
0.100
-
2.54
-
b
0.017
0.025
0.43
0.64
-
b1
0.017
0.023
0.43
0.58
-
c
0.007
0.013
0.18
0.33
-
c1
0.007
0.010
0.18
0.25
-
D
1.045
1.075 26.54
27.31
3
E
0.630
0.650 16.00
16.51
-
E1
-
0.680
-
17.27
3
E2
0.530
0.550 13.46
13.97
-
e
0.050 BSC
1.27 BSC
11
k
-
-
-
-
-
L
0.320
0.350
8.13
8.89
-
Q
0.045
0.065
1.14
1.65
8
S1
0.000
-
0.00
-
6
M
-
0.0015
-
0.04
-
N
42
42
-
Rev. 0 6/17/94
6. Measure dimension S1 at all four corners.
7. For bottom-brazed lead packages, no organic or polymeric mate-
rials shall be molded to the bottom of the package to cover the
leads.
8. Dimension Q shall be measured at the point of exit (beyond the
meniscus) of the lead from the body. Dimension Q minimum
shall be reduced by 0.0015 inch (0.038mm) maximum when sol-
der dip lead finish is applied.
9. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
10. Controlling dimension: INCH.
11. The basic lead spacing is 0.050 inch (1.27mm) between center
lines. Each lead centerline shall be located within ±0.005 inch
(0.13mm) of its exact longitudinal position relative to lead 1 and
the highest numbered (N) lead.
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate
and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
Sales Office Headquarters
NORTH AMERICA
Intersil Corporation
P. O. Box 883, Mail Stop 53-204
Melbourne, FL 32902
TEL: (407) 724-7000
FAX: (407) 724-7240
EUROPE
Intersil SA
Mercure Center
100, Rue de la Fusee
1130 Brussels, Belgium
TEL: (32) 2.724.2111
FAX: (32) 2.724.22.05
ASIA
Intersil (Taiwan) Ltd.
Taiwan Limited
7F-6, No. 101 Fu Hsing North Road
Taipei, Taiwan
Republic of China
TEL: (886) 2 2716 9310
FAX: (886) 2 2715 3029
Spec Number 518055
892
Share Link: 