HI5735KCP(1998) Просмотр технического описания (PDF) - Intersil

Номер в каталоге

Компоненты Описание

Список матч

HI5735KCP
(Rev.:1998)

12-Bit, 80 MSPS, High Speed Video D/A Converter

Intersil 

HI5735

Applications

Definition of Specifications

Bipolar Applications

Integral Linearity Error, INL, is the measure of the worst

case point that deviates from a best fit straight line of data

values along the transfer curve.

a (mV)

Differential Linearity Error, DNL, is the measure of the

error in step size between adjacent codes along the con-

verter’s transfer curve. Ideally, the step size is 1 LSB from

one code to the next, and the deviation from 1 LSB is known

as DNL. A DNL specification of greater than -1 LSB guaran-

tees monotonicity.

GLITCH ENERGY = (a x t)/2

Feedthru, is the measure of the undesirable switching noise

coupled to the output.

t (ns)

FIGURE 13. MEASURING GLITCH ENERGY

To convert the output of the HI5735 to a bipolar 4V swing, the

following applications circuit is recommended. The reference

can only provide 125µA of drive, so it must be buffered to

create the bipolar offset current needed to generate the -2V

output with all bits “off”. The output current must be converted

to a voltage and then gained up and offset to produce the

proper swing. Care must be taken to compensate for the

voltage swing and error

REF OUT

-

+

(26)

5kΩ

1/2 CA2904

5kΩ

-

+

1/2 CA2904 60Ω

HI5735

IOUT

(21)

0.1µF

50Ω

240Ω

240Ω

-

VOUT

+

HFA1100

FIGURE 14. BIPOLAR OUTPUT CONFIGURATION

Output Voltage Full Scale Settling Time, is the time

required from the 50% point on the clock input for a full scale

step to settle within an ±1/2 LSB error band.

Output Voltage Small Scale Settling Time, is the time

required from the 50% point on the clock input for a 100mV

step to settle within an 1/2 LSB error band. This is used by

applications reconstructing highly correlated signals such as

sine waves with more than 5 points per cycle.

Glitch Area, GE, is the switching transient appearing on the

output during a code transition. It is measured as the area

under the curve and expressed as a picoVolt•Time

specification (typically pV•s).

Differential Gain, ∆AV, is the gain error from an ideal sine

wave with a normalized amplitude.

Differential Phase, ∆Φ, is the phase error from an ideal

sine wave.

Signal to Noise Ratio, SNR, is the ratio of a fundamental to

the noise floor of the analog output. The first 5 harmonics

are ignored, and an output filter of 1/2 the clock frequency is

used to eliminate alias products.

Total Harmonic Distortion, THD, is the ratio of the DAC

output fundamental to the RMS sum of the harmonics. The

first 5 harmonics are included, and an output filter of 1/2 the

clock frequency is used to eliminate alias products.

Spurious Free Dynamic Range, SFDR, is the amplitude

difference from a fundamental to the largest harmonically or

non-harmonically related spur. A sine wave is loaded into the

D/A and the output filtered at 1/2 the clock frequency to

eliminate noise from clocking alias terms.

Intermodulation Distortion, IMD, is the measure of the

sum and difference products produced when a two tone

input is driven into the D/A. The distortion products created

will arise at sum and difference frequencies of the two tones.

IMD can be calculated using the following equation:

IMD = -2---0----L---o----g------(--R---(-M-R----S-M-----oS---f---A-S---m-u---m--p---l-i-a-t-u-n---dd---e--D---o--i-ff--f-e-t-h--r--ee---n--F-c--u-e---n--D-d---a-i-s--m-t--o--e-r--nt--i-ot--a--n--l-)--P---r--o----d---u---c---t--s---).

1629

Share Link: