ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 4. Dynamic Electrical Characteristics
Unless specified otherwise: 8.0 V ≤ VPWR ≤ 36 V, 3.0 V ≤ VDD ≤ 5.5 V, -40 °C ≤ TA ≤ 125 °C, GND = 0 V. Typical values are
average values evaluated under nominal conditions TA = 25 °C,VPWR = 28 V & VDD = 5.0 V, unless specified otherwise.
Parameter
Symbol
Min
Typ
Max
Unit
OUTPUT VOLTAGE SWITCHING CHARACTERISTICS
Rising and Falling edges medium slew rate (SR[1:0] = 00)(27)
VPWR = 16 V
VPWR = 28 V
VPWR = 36 V
Rising and Falling edges low slew rate (SR[1:0] = 01)(27)
VPWR = 16 V
VPWR = 28 V
VPWR = 36 V
Rising and Falling edges high slew rate / SR[1:0] = 10)(27)
VPWR = 16 V
VPWR = 28 V
VPWR = 36 V
SRR_00
SRF_00
0.164
–
0.28
–
0.34
–
SRR_01
SRF_01
0.081
–
0.14
–
0.17
–
SRR_10
SRF_10
0.29
–
0.55
–
0.68
–
0.65
0.79
0.90
0.32
0.395
0.45
1.30
1.58
1.80
V/μs
V/μs
V/μs
Rising/Falling edge slew rate matching (SRR /SRF)
Δ SR
16 V < VPWR < 36 V
0.75
1.0
1.2
Edge slew rate difference from one channel to the other in parallel mode(27)
ΔSR
16 V < VPWR < 36 V
SR[1:0] = 00
V/μs
-0.1
0.0
+0.1
SR[1:0] = 01
-0.06
0.0
+0.06
SR[1:0] = 10
-0.14
0.0
+0.14
Output Turn-ON and Turn-OFF Delays (medium slew rate: SR[1:0] = 00)(28)
t DLY_00
μs
16 V < VPWR < 36 V
32
–
128
Output Turn-ON and Turn-OFF Delays (low slew rate / SR[1:0] = 01)(28)
16 V < VPWR < 36 V
t DLY_01
μs
59
–
245
Output Turn-ON and Turn-OFF Delays (high slew rate / SR[1:0] = 10)(28)
16 V < VPWR < 36 V
t DLY_10
18
–
μs
68
Turn-ON and Turn-OFF Delay time matching (t DLY(ON) - t DLY(OFF))
Δ t RF_00
f PWM = 400 Hz, 16 V < VPWR < 36 V, duty cycle on IN[x] = 50 %, SR[1:0] = 00
-25
0.0
μs
25
Turn-ON and Turn-OFF Delay time matching (t DLY(ON) - t DLY(OFF))
Δ t RF_01
f PWM = 200 Hz, 16 V < VPWR < 36 V, duty cycle on IN[x] = 50 %, SR[1:0] = 01
-50
0.0
μs
50
Turn-ON and Turn-OFF Delay time matching (t DLY(ON) - t DLY(OFF))
Δ t RF_10
f PWM = 1.0 kHz, 16 V < VPWR < 36 V, duty cycle on IN[x] = 50 %, SR[1:0] = 10
-13
0.0
μs
13
Notes
27. Rising and Falling edge slew rates specified for a 20 to 80% voltage variation on a 5.0 Ω resistive load (see Figure 4).
28. Turn-on delay time measured as delay between a rising edge of the channel control signal (IN[0:1] = 1 or CSB) and the associated rising
edge of the output voltage up to: VHS[0:1] = VPWR / 2 (where RL = 5.0 Ω). Turn-OFF delay time is measured as time between a falling
edge of the channel control signal (IN[0 : 1] = 0 or CSB pin) and the associated falling edge of the output voltage up to the instant at which:
VHS[0:1] = VPWR / 2 (RL = 5.0 Ω)
10XS4200
15
Analog Integrated Circuit Device Data
Freescale Semiconductor